Axial SCX10-II (AX90046) Motor/ESC upgrade

It has been a while since I actually performed this upgrade, but as it was an upgrade on my main RC, I still wanted to do a write up on it.

As you may have read in Part 3 of my review / build report of my Axial SCX10-II (which you can find here), the Surpass Hobby Platinum 3100KV motor and Hobbywing EZRun Waterproof 60A ESC wasn't ideal for crawler use. Even on 2S (which is what I run in most vehicles) it was way too aggressive for crawling. I got it to a point where it was usable by adjusting the settings on both the ESC and in my Radiolink RC3S transmitter. But while it was usable, it was far from smooth in the lower end of the RPMs. Well, that was to be expected from a sensorless brushless motor.

So, what was I going to replace it with? The fan on my EZRun was kind of annoying, so I knew I wanted a fanless ESC. And I wanted to have a good dragbrake which I could adjust to my personal preferences. I considered getting a Hobbywing Quicrun WP 1080 and a high turn count brushed motor. That setup would meet my wishes, no fan, 9 levels of drag brake. I wasn't sure about going back to brushed, but at less than €75 for all parts I needed, it sure was an attractive option.

Then I stumbled across a nice little combo from Castle Creations. A brushless, sensored, waterproof crawler-oriented motor/ESC combo, consisting of their 2280KV 1406 "Slate"-series motor and the Crawler edition of their Mamba Micro X ESC. This too ran without a fan, but what really convinced me was the additional AUX-channel, which when hooked up to a free channel on your RX, allows to adjust a setting on the fly. And the dragbrake was one of the settings it could be applied to. At €200, it was quite a bit more expensive than the brushed setup, and waterproofing the sensorcable would provide me with some other challenges. But I decided to go for it.

The next day, my new toys arrived

I made the installation process a bit harder for myself than it should have been. I could have easily taken out the gearbox and work on it replacing the motor without anything else being in the way. But I didn't... To make matters worse, one of the screws of the spur gear cover was stripped (I might have mentioned the quality of the hardware before). by glueing a hex key in the screw, I managed to loosen it about 1.5 turns. That gave it enough space to carefully bend the cover out and flip it out of the way.

The motor swap was peanuts after that. Take off the pinion, loosen 2 screws, take out the old motor, put in the new motor, install the pinion, adjust the meshing, tighten everything up and done. Replacing the ESC was a matter of minutes too, as it is just stuck onto the sideplate with double sided tape. Cables were put in the receiver box and the ESCs AUX-channel was hooked up to channel 3 (VR) of my RX. A quick test to confirm everything works and then close up the receiver box and spur gear cover.

Cables need some cleaning up, but it works.

Wow, what a difference. So smooth, so much control in the low end. Not to mention the torque this thing produces. It was a big investment as it was half the price of the kit itself, but it was very much worth it.

RC Dork: The RC history Part 7

The revival.

I had rediscovered another old love, my love for music and over the years this love for music grew into a new hobby: Headphones. This is not really relevant, but I felt like mentioning it so you won't think I spent a decade without hobbies :P
One day, I found my old Corally C4.1 in a box in the attic, I think I was looking for Christmas decorations or something. And the sight of that chassis in that box instantly brought me joy. I immediately knew what to do. I had to revive the old C4.1.

Not mine, but one just like it. Picture courtesy of the internet.

I ordered a bunch of parts to give it new life. A brushless motor with a matching ESC, a new LiPo saddle pack and some new rubber. Well, things had changed a bit over the years. The battery didn't fit any of the standard mounting options so I had to stick it in with dual sided tape, which was a pain, as I didn't want to risk charging in the car. The new motor was so powerful that the ball diffs wore out in the runtime of a single battery and spares were extremely hard to find. I found some compatible parts, but the chassis, while fully featured was a pain to work on if you didn't want to take it apart completely. I had some fun, I wanted more, but I decided to abandon this project to save the chassis for historic purposes. That, and there were even less suitable spots to run an on-road competition grade RC in the area I now lived.
But my son was growing up, and started to show an interest in Monstertrucks on tv.
So, I had an idea. I would buy a small 1:18 scale cheap semi-hobbygrade monstertruck, give off-road a second chance and see if my son would like it too. If we liked it, I planned on buying a nicer monstertruck for myself and passing the small one on to my son.